 |
|
Renew IPv6 configuration of LAN that is depand on whether DHCP-PD or DNS have changed.
2. Reduce the time that is between the old RA(router lifetime=0) and new RA(new prefix or DNS), form 10-15 sec to 0.5-4 sec.
Firmware: v2.01NA Build: 16Beta02
Hardware:B1
Date: 11, Jan 2011
KERNEL: 2.6.28
SDK: 1.0, Build: 0047: Mon, 10, Jan, 2011
CheckSum:0x32DBB00E
Problem Resolved:
1. Fixed : Network Status display disconnected when connection success.So user cannot use button to disconnect
Firmware: v2.01NA Build: 16Beta01
Hardware:B1
Date: 10, Jan 2011
KERNEL: 2.6.28
SDK: 1.0, Build: 0047: Mon, 10, Jan, 2011
CheckSum:0x32D52C02
Problem Resolved:
Fixed : can't send DHCPv6 request packet
Support IPv6 Spec 1.16 - DS-Lite
*DS-Lite DHCPV6 Option(option code = 99)
*DS-Lite Manual Configuration.
Firmware: v2.01NA Build: 16Beta
Hardware:B1
Date: 07, Jan 2011
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x32D7E33B
Problem Resolved:
Support IPv6 Spec 1.16 - DS-Lite
*DS-Lite DHCPV6 Option(option code = 99)
*DS-Lite Manual Configuration.
Firmware: v2.01NA Build: 15Beta05
Hardware:B1
Date: 14, Dec 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x32A8910F
Problem Resolved:
Fixed :Automatic DHCP-PD in LAN fail
Fixed :after seting pppoev6 with create new account from ipv6 wizard ,the check mark of dhcp-pd on lan be removed
Fixed :after doing ipv6 wizard ,static dhcp-pd on lan and may no be able to work
Firmware: v2.01NA Build: 15Beta04
Hardware:B1
Date: 10, Dec 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x33D8AE83
Problem Resolved:
IPv6 1.14R Phase1
n IPv6 Wizard
n SLAAC + Stateless DHCP
n Auto-Detection Mode
n IPV6 1.14R Phase2
IPv6 1.14R Phase2
n Automatic DHCP-PD in LAN
n Static DHCP-PD in LAN
Firmware: v2.01NA Build: 15Beta03
Hardware:B1
Date: 3, Dec 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x32A81FBE
Problem Resolved:
Fixed : atuodetect.asp page value don't save
Fixed : ipv6 autoconfig nvram bug
Fixed : pppoe wizard can't do try again
Firmware: v2.01NA Build: 15Beta02
Hardware:B1
Date: 3, Dec 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x32915B24
Problem Resolved:
- Fixed : IPv6 wizard detected Autoconfigure then connect, but ipv6 wan type still is Link_Local
- IE8 run IPV6 wizard then press "prev" "Next" "Cancel" button, but no response
Firmware: v2.01NA Build: 15Beta01
Hardware:B1
Date: 2, Dec 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x32A24749
Problem Resolved:
1.Fixed : adv_ipv6_static.asp page error,IPv6 Address Range(start & end) field behind the more / 64 words
2.Fixed :setup ipv6 Autoconfiguration Type to SLAAC + Statless DHCPv6,pop warning message
Fixed :wizard_ipv6_1.asp page more error string
Fixed :When using IE8 executive ipv6 wizard ,pop warning message
Firmware: v2.01NA Build: 15Beta
Hardware:B1
Date: 1, Dec 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x32979B07
Problem Resolved:
Support IPv6 1.14R phase 1
IPv6 Wizard
Auto-Detection Mode
SLAAC + Stateless DHCP
Firmware: v2.01NA Build: 14
Hardware:B1
Date: 25, Nov 2010
KERNEL: 2.6.28
SDK: 1.0, Build: 0045: Thu, 25, Nov, 2010
CheckSum:0x321D0A7D
Problem Resolved:
- When push disconnect button ,LED should in solid status. (in pppoe manual mode)
- When push connect button without pppoe server response ,LED should in solid orange.( in pppoe manual mode)
Firmware: v2.01NA Build: 13
Hardware:B1
Date: 23, Nov 2010
KERNEL: 2.6.28